Warning: Use of undefined constant referer - assumed 'referer' (this will throw an Error in a future version of PHP) in /usr/home/essaywo/public_html/essays on line 102

Warning: Use of undefined constant host - assumed 'host' (this will throw an Error in a future version of PHP) in /usr/home/essaywo/public_html/essays on line 105

Warning: Cannot modify header information - headers already sent by (output started at /usr/home/essaywo/public_html/essays:102) in /usr/home/essaywo/public_html/essays on line 106

Warning: Cannot modify header information - headers already sent by (output started at /usr/home/essaywo/public_html/essays:102) in /usr/home/essaywo/public_html/essays on line 109
Changing A 1986 BMW 325i Clutch - School Essays

Changing A 1986 BMW 325i Clutch

Replacing a clutch in a BMW can be very difficult. There are a lot of tools needed when attempting to change one. It also can be very dangerous if not done properly. Only a certified mechanic should attempt this job. The following will explain the correct way to change a clutch.
Clean the area around the hoist you will be using, so that if you drop a nut or bolt you will be able to find it. Lay out your tools so they are easily accessible. After, your area and your tools are prepared for the job, put the car on the hoist. Raise it about a foot off the ground. Push down on the bumper of the car to make sure that it is secure on the hoist. If it is secure open the hood. Place a fender ...

Want to read the rest of this paper?
Join Essayworld today to view this entire essay
and over 50,000 other term papers

that are above the exhaust. Next get a crayon or something that can be used to mark the drive shaft, so when it is removed it can be put back on in the exact same spot it was before. Remove the drive shaft and set it out of the way. Now remove the starter. Sometimes this can be difficult. The best way to remove it is to have the car in the air. One person is under the car holding a wrench on the nut. While the other person gets above the car with a ladder and uses a ratchet to remove the two starter bolts.
Place a transmission jack under the transmission. Raise the transmission up about two inches. Remove the rear transmission mount. Lower the jack so the transmission drops far enough to easily access the wiring harness, the clutch slave cylinder, the shifter linkages, and the bell housing bolts. Disconnect all of the wires going to the transmission. Remove the shifter linkages. Some of the wires and part of the shifter linkage will have to be tied out of the way. Disconnect the ...

Get instant access to over 50,000 essays.
Write better papers. Get better grades.

Already a member? Login

CITE THIS PAGE:

APA
MLA
Chicago
Turabian

Changing A 1986 BMW 325i Clutch. (2004, September 1). Retrieved November 28, 2024, from http://www.essayworld.com/essays/Changing-A-1986-BMW-325i-Clutch/13674

"Changing A 1986 BMW 325i Clutch." Essayworld.com. Essayworld.com, 1 Sep. 2004. Web. 28 Nov. 2024. <http://www.essayworld.com/essays/Changing-A-1986-BMW-325i-Clutch/13674>

"Changing A 1986 BMW 325i Clutch." Essayworld.com. September 1, 2004. Accessed November 28, 2024. http://www.essayworld.com/essays/Changing-A-1986-BMW-325i-Clutch/13674.

JOIN NOW

Join today and get instant access to this and 50,000+ other essays

PAPER DETAILS

Added: 9/1/2004 04:59:27 PM
Category: Miscellaneous
Type: Free Paper
Words: 1115
Pages: 5

Save |

Report

SHARE THIS PAPER

SAVED ESSAYS

Save and find your favorite essays easier